How to Put a Hi-Hat Together?

 

The Hi-Hat as well as the Hi-Hat stand can look extremely complicated or rather confusing to put together if you have never tried to set it up or watched people initiate the task before. Drum lessons enable you to master the skill of putting the hi-hat easily together.

In all honesty, if you are aware of the functions of the features, as well as what might not work well, it can be pretty simple to put it together. However, it is not as straightforward as one might expect.

There are several things that can go wrong when you are setting up the hi-hat in your new drum set. We will explain the steps you need to follow in order to put it correctly together, but first, it is imperative for you to be aware of some mistakes you can remember to avoid even before you start.

YOU CAN ALSO READ: Best Portable Drum Sets

Some Big Don’ts to Avoid

When you are beginning your expedition of setting up the hi-hat with the clutch, ensure that you do not mess up the positions of the lock nuts and the non-loosened nuts. It is important you know beforehand when and where to place the nuts and on which side of the cymbal.

Next comes the rod. If you do not want to struggle with a hi-hat stand which keeps getting stuck during your playing session, you need to ensure that the rod is not bent when you are setting up the hi-hat of the drum.

We have compiled a good number of Do’s and Don’ts for the process of putting up a Hi-Hat together. But before jumping to that, it makes sense to walk you through the steps you can follow to set it up.

Steps to Follow

  • Step 1: Start with loosening the T-bolt, followed by folding out the legs. You can adjust this by setting the legs as such that either the pedal anchor does not touch, or it is not too high from the surface of the floor.
  • Step 2: Next, you have to screw the rod into the hi-hat. You should attach the clutch and make it tight enough when sticking to the rod. This will give an additional upper hand in the tightening process.
  • Step 3: In this step, you must keep an eye out for the bottom cymbal washer, as well as the felt. You must first place the washer, and then goes the felt.
  • Step 4: At this stage, you have to slide the thick or heavy cymbal in the bottom onto the seat. Usually, these bottom cymbals are far from being light attachments.
  • Step 5: Then, you must start attaching the top cymbal to the clutch. This can be done by adjusting a few things. You have to install the two lock nuts in a way that the flanges are kept away from one another. Then comes the non-loose nut, which has to go in after the cymbal and the second small felt.
  • Step 6: The clutch which is now attached to the cymbal, should then be slid onto the rod. This can be done by tightening the T-bolt when you have successfully ensured that the cymbals are at a good distance away from one another.
  • Step 7: At this point, you should ensure that the upper tube is position as such that it is at the right height for your reach or experience. You can try to keep the clutch T-bolt quite loose in order to allow you to play a little around with the adjustments. You may set the T-bolt to the desired position by simply pushing the pedal up or down.
  • Step 8: Finally, you put move and place the stand to a desired orientation with the snare and the other instruments that you will be attending. For instance, if you are used to swiveling your legs on the tube in the lower stand, you might consider moving those in order to position your snare in a more convenient position.

Some Do’s to practice

Hereby we have a list of the right things you should keep in mind while you are following the steps mentioned above.

  • When adjusting the legs, you should ensure that the pedal anchor is not touching the ground and have too much weight on it. This will help to avoid instabilities from the different directions.
  • You must set the spurs as such that they can hold the carpet properly, while supporting the pedal, after the height of the anchor has been successfully adjusted.
  • When it comes to the rod, protect it from bending too easily when transporting it. You can do this by unscrewing the rod every time.
  • You must ensure that you put the bottom cymbal first, given that these are usually thicker.
  • When tightening the nuts of the clutch, play around with how much the top cymbal can move.

Some Don’ts to avoid

  • Avoid setting the legs of the hi-hat too high above the floor surface. This will not be able to take the pressure when you are pushing the pedal down.
  • Look out for the spurs affecting the floor if your floor is made of wood. The spurs can be too sharp and may even be detrimental for the surface unless you are using it on top of carpets and rugs.
  • Try to avoid stripping the thread that links the top part of the rod to the internal functioning of the hi-hat.
  • You can use any kind of cymbals- you do not have to use only hi-hat cymbals. You may try crash cymbals too.

Concluding Remarks

You are now aware of all the important steps you have to follow in order to put a hi-hat together. Furthermore, the aforementioned dos and don’ts should give you a necessary heads-up about what to undertake and what to try to avoid in the process of setting it up.

Leave a Comment